Choose a year: 2021 : 2020 : 2019 : 2018 : 2017 : 2016 : 2015 : 2014 : 2013 : 2012: 2011: 2010: 2009 : 2008 : 2007: 2006 : 2005 : 2004 : 2003 : 2002 : 2001 : 2000 : 1999

Lin, D., Lastra, R., and Finch, J.A., Comparison of stereological correction procedures for liberation measurements by use of a standard material. Trans. IMM, Sect. C., Vol. 108, Sept.-Dec. 1999

R.J. Rajamani, B.K. Mishra, P. Songfack and R. Venugopal, Millsoft- simulation software for tumbling-mill design and trouble shooting. Mining Engineering, Vol. 51 no.12, December 1999

G Micco, P Netti, L Nicolais, A Collina, G Astarita. A novel approach for grinding operation scale-up. Chemical Engineering Science, Vol.55 no.8, Dec. 1999

A.L. Grabowski, Improved crushing chamber of a cone crusher. Trans.Instn Min. Metall. (Sect, C), Vol. 108, May-August 1999.

D.J. Barratt, M.N. Brodie and M. Pfeifer, SAG milling design trends, comaparative economics, mill sizes and drives. CIM Bulletin, Vol. 92 no.1035, Oct. 1999.

CM Evertsson. Modelling of flow in cone crushers. Minerals Engineering, Vol.12, no.12, Nov.1999

P Radziszewski. Comparing three DEM charge motion models. Minerals Engineering, Vol.12, no.12, Nov.1999

PB Rajendran Nair. Breakage parameters and the operating variables of a circular fluid energy mill part-I breakage distribution parameter. Powder Technology, Vol.106 no.1-2, Nov. 1999

PB Rajendran Nair. Breakage parameters and the operating variables of a circular fluid engery mill part-II breakage rate parameter. Powder Technology, Vol.106 no.1-2, Nov. 1999

LG Austin. A discussion of equations for the analysis of batch grinding data. Powder Technology, Vol.106 no.1-2, Nov. 1999

H Berthiaux, JA Dodds. Modelling fine grinding in a fluidized bed opposed jet mill part 1: batch grinding kinetics. Powder Technology, Vol.106 no.1-2, Nov. 1999

H Berthiaux, J Dodds. Modelling fine grinding in a fluidized bed opposed jet mill Part II. continuous grinding. Powder Technology, Vol.106 no.1-2, Nov. 1999

F Muller, R Polke. From the product and process requirements to the milling facility. Powder Technology, Vol.105 no.1-3, Nov. 1999

A Kwade. Wet comminution in stirred media mills - research and its practical application. Powder Technology, Vol.105 no.1-3, Nov. 1999

O Lecoq, P Guigon. A grindability test to study the influence of material processing on impact behaviour. Powder Technology, Vol.105 no.1-3, Nov. 1999

V Werner, K Schonert. Lab-scale roller table mill for investigating the grinding behaviour of coal. Powder Technology, Vol.105 no.1-3, Nov. 1999

J Tomas. Impact crushing of concrete for liberation and recycling. Powder Technology, Vol.105 no.1-3, Nov. 1999

K Nielsen. Grindability enhancement by blast induced microcracks. Powder Technology, Vol.105 no.1-3, Nov. 1999

C Couroyer. Breakage of macroporous alumina beads under compressive loading: simulation and experimental validation. Powder Technology, Vol.105 no.1-3, Nov. 1999

C Thornton. Numerical simulations of agglomerate impact breakage. Powder Technology, Vol.105 no.1-3, Nov. 1999

O Gutsche. Fracture kinetics of particle bed comminution - ramifications for fines production and mill optimization. Powder Technology, Vol.105 no.1-3, Nov. 1999

G Baudet. Two dimensions comminution of kaolinite clay particles. Powder Technology, Vol.105 no.1-3, Nov. 1999

R Hogg. Breakage mechanisms and mill performance in ultrafine grinding. Powder Technology, Vol.105 no.1-3, Nov. 1999

P De Donato. Chemical surface modifications of sulphide minerals after comminution. Powder Technology, Vol.105 no.1-3, Nov. 1999

JC Benezet. Grinding and pozzolanic reactivity of quartz powders. Powder Technology, Vol.105 no.1-3, Nov. 1999

O Tsoungui. Numerical model of crushing of grains inside two-dimensional granular materials. Powder Technology, Vol.105 no.1-3, Nov. 1999

DW Fuerstenau. The effect of ball size on the energy efficiency of hybrid high-pressure roll mill/ball mill grinding. Powder Technology, Vol.105 no.1-3, Nov. 1999

J Strazisar. Attrition as a process of comminution and separation. Powder Technology, Vol.105 no.1-3, Nov. 1999

K Yildirim, LG Austin. The modeling of dry grinding of quartz in tumbling media mills. Powder Technology, Vol.105 no.1-3, Nov. 1999

A Misra. Particle motion and energy distribution in tumbling ball mills. Powder Technology, Vol.105 no.1-3, Nov. 1999

C Varinot, J Dodds. Prediction of the product size distribution in associations of stirred bead mills. Powder Technology, Vol.105 no.1-3, Nov. 1999

JC Roux. Modeling of the particle breakage kinetics in the wet mills for the paper industry. Powder Technology, Vol.105 no.1-3, Nov. 1999

F Muller, M Schafer. Model based evaluation of grinding experiments. Powder Technology, Vol.105 no.1-3, Nov. 1999

DI Hoyer. The discrete element method for fine grinding scale-up in HiCOM mills. Powder Technology, Vol.105 no.1-3, Nov. 1999

D Eskin. Simulation of jet milling. Powder Technology, Vol.105 no.1-3, Nov. 1999

U Sander, K Schonert. Operational conditions of a screw feeder equipped high pressure roller mill. Powder Technology, Vol.105 no.1-3, Nov. 1999

L Aboussouan, MN Pons. Steel scrap fragmentation by shredders. Powder Technology, Vol.105 no.1-3, Nov. 1999

S Zhang, E Forssberg. Intelligent liberation and classification of electronic scrap. Powder Technology, Vol.105 no.1-3, Nov. 1999

I Habil, E Gock. Eccentric vibratory mills - theory and practice. Powder Technology, Vol.105 no.1-3, Nov. 1999

U Bock, K Schonert. Charge motion model for vibration mills with high excitation. Powder Technology, Vol.105 no.1-3, Nov. 1999

S Molina Boisseau, N Le Bolay. Fine grinding of polymers in a vibrated bead mill. Powder Technology, Vol.105 no.1-3, Nov. 1999

S. Tasirin. Experimental investigation on fluidized bed jet grinding. Powder Technology, Vol.105 no.1-3, Nov. 1999

T Inoue. Development of a centrifugal mill - a chain of simulation, equipment design and model validation. Powder Technology, Vol.105 no.1-3, Nov. 1999

F Rubiera, JJ Pis. Effect of the grinding behaviour of coal blends on coal utilisation for combustion. Powder Technology, Vol.105 no.1-3, Nov. 1999

I Habil, K Husemann. The influence of suspension properties on ultra-fine grinding in stirred ball mills. Powder Technology, Vol.105 no.1-3, Nov. 1999

HB Fadhel, C Frances. Investigations on ultra-fine grinding of titanium dioxide in a stirred media mill. Powder Technology, Vol.105 no.1-3, Nov. 1999

M Becker. Comminution of ceramics in stirred media mills and wear of grinding beads. Powder Technology, Vol.105 no.1-3, Nov. 1999

A Kwade. Determination of the most important grinding mechanism in stirred media mills by calculating stress intensity and stress number. Powder Technology, Vol.105 no.1-3, Nov. 1999

K Belaroui, MN Pons. Wet grinding of gibbsite in a bead-mill. Powder Technology, Vol.105 no.1-3, Nov. 1999

J Theuerkauf. Theoretical and experimental investigation on particle and fluid motion in stirred media mills. Powder Technology, Vol.105 no.1-3, Nov. 1999

JA Herbst. Object components for comminution system softsensor design. Powder Technology, Vol.105 no.1-3, Nov. 1999

RR Klimpel, C Frances. The selection of wet grinding chemical additives based on slurry rheology control. Powder Technology, Vol.105 no.1-3, Nov. 1999

KL Sandvik. Change from pressure crushing in roller mills to impact crushing in production of mineral sand. Powder Technology, Vol.105 no.1-3, Nov. 1999

A Thomas, LO Filippov. Fractures, fractals and breakage energy of mineral praticles. Int. J. Mineral Processing, Vol.57, no.4, Oct. 1999

Shi, F.N., and Napier-Munn, T.J., Estimation of shear rates inside a ball mill. Int. J. Mineral Processing, Vol.57, no.3, Sept. 1999

NJ Welham. Formation of TiB2 from rutile by room temperature ball milling. Minerals Engineering, Vol.12, no.10, Oct. 1999

RJ Deshpande, KA Natarajan. Studies on grinding media wear and its effect on flotation of ferrugenous phosphate ore. Minerals Engineering, Vol.12, no.9, 1999

A Datta, BK Mishra, RK Rajamani. Analysis of power draw in ball mills by the discrete element method, Canadian Metallurgical Quarterly, Vol.38 no.2, 1999

C Fernandes, AEC Peres. Optimisation of the grinding circuit at Arafertil, Brazil, Minerals Engineering, Vol.12, no.8, 1999

C Sosa-Blanco, D Hodouin, C Bazin, C Lara-Valenzuela, J Salazar. Integrated simulation of grinding and flotation application to a lead-silver ore, Minerals Engineering, Vol.12, no.8, 1999

Songfack, Poly Hold-up studies in a pilot scale continuous ball mill: dynamic variations due to changes in operating variables, Int. J. Mineral Processing, Vol.57, no.2, 1999

Gay, Stephen L. Numerical verification of a non-preferential-breakage liberation model, Int. J. Mineral Processing, Vol.57, no.2, 1999

Shaw-Bing Wen, Chin-Wen Lai, She-Chun Cheng and Chi-Yen Huang, Comminution of air-cooled slag for recovery of metal grains, Trans. Instn. Min. Metall. (Sect, C), Vol. 107, Sept-Dec. 1998

A J Lawry, A Schuurmans and K B Quast, Laboratory studies in comminution: Part III. Effect of mill arameters on grinding a tin ore, The AusIMM Proceedings, Vol. 33, no.1, 1999

A Schuurmans and K B Quast, Laboratory studies in comminution: Part IV. Effect of feed sizing on the grinding of a tin ore, The AusIMM Proceedings, Vol. 33, no.1, 1999.

K B Quast, Laboratory studies in comminution: Part V. Simulation of an industrial rod mill product, The AusIMM Proceedings, Vol. 33, no.1, 1999.

K B Quast and P G Hicks, Laboratory studies in comminution: Part VI. The specific rate of breakage for rod and ball milling of quartz, The AusIMM Proceedings, Vol. 33, no.1, 1999.

L.G. Austin, Modification of ball mill simulator models to allow for unequal residence times, Minerals and Metallurgical Processing, Vol. 16 No.1, Feb. 1999

A. Datta and B.K. Mishra, Power draw estimation of ball mills using neural networks, Minerals and Metallurgical Processing, Vol. 16 No.1, Feb. 1999