Choose a year: 2021 : 2020 : 2019 : 2018 : 2017 : 2016 : 2015 : 2014 : 2013 : 2012: 2011: 2010: 2009 : 2008 : 2007: 2006 : 2005 : 2004 : 2003 : 2002 : 2001 : 2000 : 1999

Shi, F. N.,, Development of a power-draw model for estimation of the dynamic recirculating load of swing hammer mills with internal classifiers. Trans.IMM, Sec. C, Volume 111 Sept/Dec (2002)

Bhagat, R. P. Sil, S. K. Srivastava, J. P., , Effect of polymeric additive and other variables on efficiency of grinding of limestone. Trans.IMM, Sec. C, Volume 111 Sept/Dec (2002)

Jankovic, A., and Valery, W., Mine to mill optimisation for conventional grinding circuits- a scoping study. Journal of Mining and Metallurgy, Volume 38 Numbers 1-4, Section A (2002)

Oder, R.R., An evaluation of the Alpha Prototype MagMill for dry coal cleaning. Coal Preparation, Vol.22 No.6, 2002

Loveday, B.K., and Whiten, W.J., Application of a rock abrasion model to pilot-plant and plant data for fully and semi-autogenous grinding. Trans. IMM Section C, Vol. 111/Proc. Australas.IMM, Vol.307, Jan.-April 2002

Zambrano, A. R., General work input functions for sizing grinding ball mills. Minerals and Metallurgical Processing, Vol.19 No.4, 2002

D. Tromans, J.A. Meech. Fracture toughness and surface energies of minerals: theoretical estimates for oxides, sulphides, silicates and halides. Minerals Engineering, Vol.15, no.12, 2002

T.A. Apelt, S.P. Asprey, N.F. Thornhill. Inferential measurement of SAG mill parameters II: state estimation. Minerals Engineering, Vol.15, no.12, 2002

T.A. Apelt, S.P. Asprey, N.F. Thornhill. Inferential measurement of SAG mill parameters III: inferential models. Minerals Engineering, Vol.15, no.12, 2002

P. Radziszewski. Exploring total media wear. Minerals Engineering, Vol.15, no.12, 2002

L. Godet-Morand, A. Chamayou, J. Dodds. Talc grinding in an opposed air jet mill: start-up, product quality and production rate optimization. Powder Technology, Vol.128 no.2-3, 2002

Teke, E., Yekeler, M., Ulusoy, U., and Canbazoglu, M., Kinetics of dry grinding of industrial minerals: calcite and barite. International Journal of Mineral Processing, vol.67 no.1-4, 2002

Deniz, V., and Onur, T., Investigation of the breakage kinetics of pumice samples as dependent on powder filling in a ball mill. International Journal of Mineral Processing, vol.67 no.1-4, 2002

Fuerstenau, D.W., and Abouzeid, A.Z.M., The energy efficiency of ball milling in comminution. International Journal of Mineral Processing, vol.67 no.1-4, 2002

D.N. Whittles, S.W. Kingman, D.J. Reddish. Application of numerical modelling for prediction of the influence of power density on microwave-assisted breakage. International Journal of Mineral Processing, vol.68 no.1-4, 2002

P.W. Cleary, R. Morrisson, S. Morrell. Comparison of DEM and experiment for a scale model SAG mill. International Journal of Mineral Processing, vol.68 no.1-4, 2002

A.D. Salman, C.A. Biggs, J. Fu, I. Angyal, M. Szabo, M.J. Hounslow. An experimental investigation of particle fragmentation using single particle impact studies. Powder Technology, Vol.128 no.1, 2002

E.T. Stamboliadis. A contribution to the relationship of energy and particle size in the comminution of brittle particulate materials. Minerals Engineering, Vol.15, no.10, 2002

S. Nikolov. A performance model for impact crushers. Minerals Engineering, Vol.15, no.10, 2002

Gopal, A.V., and Rao, P.V., Modelling of grinding of silicon carbide with diamond wheels. Mineral Processing and Extractive Metallurgy Review, Vol. 23 No.1, Jan-March, 2002

M. Kostoglou, A.J. Karabelas. An assessment of low-order methods for solving the breakage equation. Powder Technology, Vol.127 no.2, 2002

P.L.C. Lage. Comments on the ''An analytical solution to the population balance equation with coalescence and breakage-the special case with constant number of particles'' by D.P. Patil and J.R.G. Andrews. Chemical Engineering Science, vol.57 no.19, 2002

Wiegel, R. L., Size reduction/mineral liberation simulation for a magnetic taconite concentrator. Minerals and Metallurgical Processing, Vol.19 No.3, August 2002

S. Nitta, A. Bissombolo, T. Furuyama, S. Mori. Relationship between Bond's work index (Wi) and uniformity constant (n) of grinding kinetics on Tower mill milling limestone. Int. J. Mineral Processing, Vol.66, no.1-4, 2002

Y. Peng, S. Grano, J. Ralston, D. Fornasiero. Towards prediction of oxidation during grinding I. Galena flotation. Minerals Engineering, Vol.15, no.7, 2002

G.M. Monama, M.H. Moys. DEM modelling of the dynamics of mill startup. Minerals Engineering, Vol.15, no.7, 2002

B.K. Mishra and C. Thornton. An improved contact model for ball mill simulation by the discrete element method. Advanced Powder Technology, Vol. 13, No. 1, 2002

F.N. Shi, T.J. Napier-Munn. Effects of slurry rheology on industrial grinding performance. International Journal of Mineral Processing, vol.65 no.3-4, 2002

M.A. van Nierop, M.H. Moys. Axial mixing of slurry in an autogenous grinding mill. International Journal of Mineral Processing, vol.65 no.3-4, 2002

H. Dong, M.H. Moys. Assessment of discrete element method for one ball bouncing in a grinding mill. International Journal of Mineral Processing, vol.65 no.3-4, 2002

McCaffery, K. M. Katom, M. Craven, J. W., Ongoing evolution of advanced SAG mill control at Ok Tedi. Minerals and Metallurgical Processing. Volume 19 Number 2, 2002

R. B. Diemer, J. H. Olson. A moment methodology for coagulation and breakage problems: Part 1-analytical solution of the steady-state population balance. Chemical Engineering Science, vol.57 no.12, 2002

R.B. Diemer, J.H. Olson. A moment methodology for coagulation and breakage problems: Part 2-moment models and distribution reconstruction. Chemical Engineering Science, vol.57 no.12, 2002

S. Voropayev, D. Eskin. Optimal particle acceleration in a jet mill nozzle. Minerals Engineering, Vol.15, no.6, 2002

Clarke, N.C., Henley, K.J., Wu, T., and le Page, M., Autogenous milling- ellects on flotation of Mt. Lyell copper ore. CIM Bulletin, Vol. 95 Number 1060, April 2002

J.B. Yianatos, M.A. Lisboa, D.R. Baeza. Grinding capacity enhancement by solid concentration control of hydrocyclone underflow. Minerals Engineering, Vol.15, no.5, 2002

L.G. Austin. A treatment of impact breakage of particles. Powder Technology, Vol.126 no.1, 2002

B.G. Kim, S.K. Choi, H.S. Chung, J.J. Lee, F. Saito. Grinding characteristics of crystalline graphite in a low-pressure attrition system. Powder Technology, Vol.126 no.1, 2002

Man, Y.T., Why is the Bond ball mill grindability test done the way it is done? The European Journal of Mineral Processing and Environmental Protection, Vol. 2 Number 1, 2002

F.S. Bourgeois, G.A. Banini. A portable load cell for in-situ ore impact breakage testing. International Journal of Mineral Processing, vol.65 no.1, 2002

F.N. Shi. Investigation of the effects of chrome ball charge on slurry rheology and milling performance. Minerals Engineering, Vol.15, no.4, 2002

R. Lestage, A. Pomerleau, D. Hodouin. Constrained real-time optimization of a grinding circuit using steady-state linear programming supervisory control. Powder Technology, Vol.124 no.3, 2002

O. Galan, G.W. Barton, J.A. Romagnoli. Robust control of a SAG mill. Powder Technology, Vol.124 no.3, 2002

S.M. Iveson. Limitations of one-dimensional population balance models of wet granulation processes. Powder Technology, Vol.124 no.3, 2002

C. Tangsathitkulchai. Acceleration of particle breakage rates in wet batch ball milling. Powder Technology, Vol.124 no.1-2, 2002

H. Cho, L.G. Austin. The equivalence between different residence time distribution models in ball milling. Powder Technology, Vol.124 no.1-2, 2002

K. Tanaka, M. Nishida, T. Kunimochi, T. Takagi. Discrete element simulation and experiment for dynamic response of two-dimensional granular matter to the impact of a spherical projectile. Powder Technology, Vol.124 no.1-2, 2002

A. Datta, R.K. Rajamani. A direct approach of modeling batch grinding in ball mills using population balance principles and impact energy distribution. International Journal of Mineral Processing, vol.64 no.4, 2002

J. Conway-Baker, R.W. Barley, R.A. Williams, X. Jia, J. Kostuch, B. McLoughlin, D.J. Parker. Measurement of the motion of grinding media in a vertically stirred mill using positron emission particle tracking (PEPT). Minerals Engineering, Vol.15, no.1-2, 2002

A.-Q. Nguyen, K. Husemann, W. Oettel. Comminution behaviour of an unconfined particle bed. Minerals Engineering, Vol.15, no.1-2, 2002

R.M. Braun, J. Kolacz, D.I. Hoyer. Fine dry comminution of calcium carbonate in a Hicom mill with an Inprosys air classifier. Minerals Engineering, Vol.15, no.3, 2002

Apelt, T.A. (2002). Inferential Measurement Models for Semi-autogenous Grinding Mills. PhD Thesis. University of Sydney.

L.M. Tavares, R.P. King. Modeling of particle fracture by repeated impacts using continuum damage mechanics. Powder Technology, Vol.123 no.2-3, 2002

R. Greenwood, N. Rowson, S. Kingman, G. Brown. A new method for determining the optimum dispersant concentration in aqueous grinding. Powder Technology, Vol.123 no.2-3, 2002

S. Molina-Boisseau, N. Le Bolay. The mixing of a polymeric powder and the grinding medium in a shaker bead mill. Powder Technology, Vol.123 no.2-3, 2002

S. Molina-Boisseau, N. Le Bolay, M.-N. Pons. Fragmentation mechanism of poly(vinyl acetate) particles during size reduction in a vibrated bead mill. Powder Technology, Vol.123 no.2-3, 2002

D. Eskin, H. Kalman. Problems of optimal particle acceleration on straight linear blades of centrifugal rotor-impact mills. Powder Technology, Vol.123 no.1, 2002

Ajaal, T. Smith, R. W. Yen, W. T., The Development and Characterization of a Ball Mill for Mechanical Alloying. Canadian Metallurgical Quarterly, Vol. 41 No. 1, 2002

F. Garcia, N. Le Bolay, C. Frances. Changes of surface and volume properties of calcite during a batch wet grinding process. Chemical Engineering Journal, vol.85 no.2-3, 2002

L.G. Austin, H. Cho. An alternative method for programming mill models. Powder Technology, Vol.122 no.2-3, 2002

N. Kotake, K. Suzuki, S. Asahi, Y. Kanda. Experimental study on the grinding rate constant of solid materials in a ball mill. Powder Technology, Vol.122 no.2-3, 2002

A. Kwade, J. Schwedes. Breaking characteristics of different materials and their effect on stress intensity and stress number in stirred media mills. Powder Technology, Vol.122 no.2-3, 2002

R. Hogg, A.J. Dynys, H. Cho. Fine grinding of aggregated powders. Powder Technology, Vol.122 no.2-3, 2002

Q.Q. Zhao, G. Schurr. Effect of motive gases on fine grinding in a fluid energy mill. Powder Technology, Vol.122 no.2-3, 2002

K. Schonert, U. Sander. Shear stresses and material slip in high pressure roller mills. Powder Technology, Vol.122 no.2-3, 2002

Q. Zhang, J. Lu, F. Saito. Mechanochemical synthesis of LaCrO3 by grinding constituent oxides. Powder Technology, Vol.122 no.2-3, 2002